![]() ![]() In this case, the writer compares her table data to the work of other authors and extracts key test results and quantities from the table to discuss in the paper’s text. This implies slumping, which could increase the effective porosity significantly.Ībove, we see how the table caption and supporting text are tightly intertwined, with the aim of describing a trend. This effective porosity seems high, but the dip of bedding in the study area is opposite the regional dip. As shown in Table 1, the borehole dilution hydraulic conductivity values for wells B2 and B4 agree reasonably well with their corresponding slug test values, assuming an effective porosity between 0.01 and 0.05. The hydraulic conductivities computed from the borehole dilution test velocities are significantly lower than those predicted by Huang and Sheltons' core analysis of Middle Kittanning coal. Water velocities and hydraulic conductivities of the Lower Kittanning coal at the Kaufmann site in Clearfield County, Pennsylvania, from slug tests, November 1991, and borehole dilution (BD) tests, November 1992. The hydraulic conductivities computed from the borehole dilution test velocities for these wells range over an order of magnitude-a reasonable spread for hydraulic properties of close, but varying, test sites. Requires the float package, i.e.Table 1 summarizes the results of borehole dilution testing and slug testing on wells B2, B3, and B4. ![]() Places the float at precisely the location in the LaTeX code. Override internal parameters LaTeX uses for determining "good" float positions. Place the float here, i.e., approximately at the same point it occurs in the source text (however, not exactly at the spot) The placement specifier parameter exists as a compromise, and its purpose is to give the author a greater degree of control over where certain floats are placed. However, there may be times when you disagree, and a typical example is with its positioning of figures. The previous section mentioned how floats are used to allow LaTeX to handle figures while maintaining the best possible presentation. To create a figure that floats, use the figure environment. ! LaTeX Error: Too many unprocessed floats. LaTeX by default can cope with maximum 18 floats and a symptomatic error is: The skill is to space them out within your text so that they intrude neither on the thread of your argument or discussion nor on the visual balance of the typeset pages.Īs with various other entities, there exist limitations on the number of unprocessed (placed) floats in line. In this case, LaTeX stacks them all up and prints them together if possible, or leaves them to the end of the chapter in protest. This can be changed by moving the Table or Figure definition to an earlier or later point in the text, or by adjusting some of the parameters which control automatic floating.Īuthors sometimes have many floats occurring in rapid succession, which raises the problem of how they are supposed to fit on the page and still leave room for text. If there is not enough room on the current page, the float is moved to the top of the next page. LaTeX automatically floats Tables and Figures, depending on how much space is left on the page at the point that they are processed. They always have a caption describing them and they are always numbered so they can be referred to from elsewhere in the text. Floats are there to deal with the problem of the object that won't fit on the present page and to help when you really don't want the object here just now.įloats are not part of the normal stream of text, but separate entities, positioned in a part of the page to themselves (top, middle, bottom, left, right, or wherever the designer specifies). LaTeX by default recognizes "table" and "figure" floats, but you can define new ones of your own (see Custom floats below). 6.1 Tip for figures with too much white spaceįloats are containers for things in a document that cannot be broken over a page.It would also be good if LaTeX could apply principles similar to when it arranges text to look its best to arrange pictures as well. What we need is a way of defining figures. To start with, we want a way of adding captions, and to be able to cross-reference. However, just having a picture stuck in between paragraphs does not look professional. The previous chapter introduced importing graphics. Collaborative Writing of LaTeX Documents.Scientific Reports (Bachelor Report, Master Thesis, Dissertation). ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |